- #Wxtoimg error waveinopen failed upgrade
- #Wxtoimg error waveinopen failed code
- #Wxtoimg error waveinopen failed tv
One laptop is an HP Envy and the other is a Lenovo X1 Carbon Gen 3. With one machine I can get a certain app installed and with the other machine it will not install! In summary, I have two laptops running identical OS’s. I tried a couple of different libraries, but eventually settled with the library from which works well with my display.Here is an interesting little problem for all you geeks out there, and is one that has this particular geek completely stumped. The I2C display is a generic display, purchased from eBay, and uses the PCF8574 I2C receiver IC. There's two sketches, the GPS clock itself, and a simple test receiver sketch to check everything's working as it should. The GPS module will be configured by the sketch itself, to 200mS refresh rate. I've added a 4x20 LCD display, with I2C piggyback interface board, and the u-blox GPS module we've used in the GPS logger.
#Wxtoimg error waveinopen failed code
I'll be re-using the code from the quick and dirty 7-segment GPS clock here, and some of the code for the transmit function from the dehumidifier project. The transmitter will be triggered randomly, at least once every 24 hours, or by a push button connected to pin 12. The idea is to have a master clock, GPS locked with built in 433 MHz transmitter, which will send an accurate time signal to the other clocks to bring them into sync.
#Wxtoimg error waveinopen failed upgrade
I also wish to upgrade the Astronomical clock project, as the DS1307 often drifts about, losing and gaining seconds as it feel like it. I've got a few clock projects in the back of my mind, and this is a bit of an aside to them all. It's drawing about 165mA at that voltage, so a supply is not too challenging! It seems to want about 6.5 VDC to operate, and has even remembered the settings it had before the power supply failed. I removed the transformer, and connected the workshop power supply between the end of the rectifier diode, and ground. I thought I'd remove the ghastly existing "switched-mode" blocking oscillator, and replace it with something. It looks as though the insulation had failed on the transformer, and destroyed the semi-conductors in the drive-side of the supply. I opened it up and expected to find a mass of blackened bits, but no. lord knows what would have happened if it had tried to short out the mains without the protection of a fuse. (If you have one of these awful modulators, time to stop using it!) Damned glad I fitted one. "It's bound to be the modulator" I thought.
#Wxtoimg error waveinopen failed tv
Well, settling down for an afternoon of vintage TV fun, I switched the video rack on. I wrote about it here. Please take a moment to read this, if you haven't seen it before. Workshop penny shown for scale.Īnd finally Mrs Doz states the antenna can live on the corner of the shed. The case has an attractive smoked top, which allows me to see the status LEDs. Sadly I didn't notice the Raspberry Pi had moved to an odd angle before the epoxy set :(. The Raspberry Pi, Bias T (getting it's 5 volt supply from the raspberry Pi itself), and the SDR receiver are all mounted up in a small case. Wput -B -u -dont-continue -reupload -tries=5 -binary -verbose -reupload ~/weather/Folder*/*.*
Sudo echo "0" > /sys/class/gpio/gpio24/value Sudo echo "1" > /sys/class/gpio/gpio22/value Sudo echo "out" > /sys/class/gpio/gpio22/direction # reads and creates folder with current date / time (i.e 05-30-2019_07-48 *windows friendly*) Receive_and_process.sh now looks like this.
Sudo echo "1" > /sys/class/gpio/gpio24/value Sudo echo "out" > /sys/class/gpio/gpio24/direction Schedule_all.sh needs the following lines at the end. Schedule_all.sh and receive_and_process.sh To drive the LEDs, there are two bash scripts to alter.